Snowboard Wax
Snowboard Rants, News, Articles, Reviews & More!
Snowboarding Wax: What Should Be Done!
ARTICLE BY: Daryl Marly
Have you ever been cruising your way down a mountain just enjoying the ride, the scenery and everything else, when suddenly along comes a nasty wide open expanse of flat. Do you ever wonder why it is that there always seems to be a whole load of people, some on the worst rental boards you can imagine, that manage to overtake you with ease, just managing to maintain enough speed to get over the ridge and carry on down the mountain? At times like these, which all of us have experienced, you may wonder what you are doing that is not quite right. Well, this darn unfortunate occurrence may be due to you either having poorly waxed your board, of worse still, not having waxed it at all! This brief article looks at the why’s and how’s of waxing your snowboard.
Why bother?!
Simply put, if you don’t wax your board you are missing out on a smoother, faster and therefore more responsive/ enjoyable ride. Wax can make a huge difference, if done properly. Waxing is one of the easiest ways to improve board performance adding the benefits of less tiresome riding and extending the useful life of the base of you board. Waxing is best done in combination with other board enhancing procedures e.g. edge tuning.
How to wax your snowboard
Equipment you need (buy or borrow it!):
Waxing method
If you’re lazy and slightly loaded, with time on your hands you could abort this article right now and wax your board the easy way, by getting someone else to do it. Today it is very easy to either post it or hand it to either a local snowboard shop or specialist service that can do a multitude of waxing and other board enhancement procedures.
If you feel the need to gain an extra, very useful, skill read on. Choose the appropriate wax for the temperature of the snow. Hard wax is typically used for cold conditions, is harder to administer and lasts least. Warmer conditions use softer wax that is far easier to put on you boards base. If unsure of what the temperature is outside you could use a general snowboarding wax suitable in most conditions.
Lay the board upside down, in a sturdy position. If there is old wax you would like to get rid of then use a wax removing solvent spray on the base. This stuff stinks, so use a very well ventilated area. Absorb and wipe off the wax with a cloth. Ideally this is done the night before the waxing proper. Removing the old wax is done mainly so that the correct wax for the conditions will end up on the board. Melt wax droplets with the iron in a snake fashion from tip to tail, slowly and methodically. Gaps of about 1-2cm between drops work fine for me. It helps to drip the wax off a corner of the wax block. Remember not to let the iron get so hot that smoke is produced.
After having applied the drops of wax you must next proceed in a wax on wax off style from tip to tail, nice and slowly with the iron. Spread a thin, almost un-noticeable layer across the board. A great method for embedding the wax evenly and deep into the base of the board is to use roughly circular, real slow motions from side to side and along the base. Don’t spend too long on one area of the base or the base may get a little damaged.
Leave the base to cool for as long as possible e.g. 12 hours is fine. Cooling for only a few hours will work, if you have to. This gives the base time to really absorb and retain the wax through the resultant cooling/ hardening.
Next you must scrape the base of the board in a tip to tail direction only with a firm, straight plastic or metal edged scraper. Try to remove all wax to create a perfectly smooth flat base. This part is the most tiring, but also very important. To remove particularly stubborn sections of wax you can momentarily bend the scraper a little to focus your energies on a smaller area.
When the excess wax has been removed its then time to polish the base with a soft bush in the same fashion as when ironing. Afterwards sternly use the harsh brush (often have metal protrusions) in a tip to tail only fashion to add structure to the base.
There you go, its ready to ride!
Generally it’s a good idea to wax your board once every 3 days of use. Waxing should be more frequent if you ride really hard or enjoy ice or hard-packed snow conditions. To reduce the board damaging effects of oxidation of the base from UV radiation/ other influences from the environment why not wax the base for transport and long snowless summers.
Why bother?!
Simply put, if you don’t wax your board you are missing out on a smoother, faster and therefore more responsive/ enjoyable ride. Wax can make a huge difference, if done properly. Waxing is one of the easiest ways to improve board performance adding the benefits of less tiresome riding and extending the useful life of the base of you board. Waxing is best done in combination with other board enhancing procedures e.g. edge tuning.
How to wax your snowboard
Equipment you need (buy or borrow it!):
- Waxing iron (flat with no steam holes!). An old iron works just as well
- Plastic wax scraper to remove excess wax
- Ideally a good, level bench with two level stands or clamps (plastic or metal)
- Good range of waxes for different temperatures
- Soft and a hard brush for polishing
- Ideally a well ventilated dry room, or garage, or simply outside if you have to
- Ideally an old sheet for the wax to drip on to
Waxing method
If you’re lazy and slightly loaded, with time on your hands you could abort this article right now and wax your board the easy way, by getting someone else to do it. Today it is very easy to either post it or hand it to either a local snowboard shop or specialist service that can do a multitude of waxing and other board enhancement procedures.
If you feel the need to gain an extra, very useful, skill read on. Choose the appropriate wax for the temperature of the snow. Hard wax is typically used for cold conditions, is harder to administer and lasts least. Warmer conditions use softer wax that is far easier to put on you boards base. If unsure of what the temperature is outside you could use a general snowboarding wax suitable in most conditions.
Lay the board upside down, in a sturdy position. If there is old wax you would like to get rid of then use a wax removing solvent spray on the base. This stuff stinks, so use a very well ventilated area. Absorb and wipe off the wax with a cloth. Ideally this is done the night before the waxing proper. Removing the old wax is done mainly so that the correct wax for the conditions will end up on the board. Melt wax droplets with the iron in a snake fashion from tip to tail, slowly and methodically. Gaps of about 1-2cm between drops work fine for me. It helps to drip the wax off a corner of the wax block. Remember not to let the iron get so hot that smoke is produced.
After having applied the drops of wax you must next proceed in a wax on wax off style from tip to tail, nice and slowly with the iron. Spread a thin, almost un-noticeable layer across the board. A great method for embedding the wax evenly and deep into the base of the board is to use roughly circular, real slow motions from side to side and along the base. Don’t spend too long on one area of the base or the base may get a little damaged.
Leave the base to cool for as long as possible e.g. 12 hours is fine. Cooling for only a few hours will work, if you have to. This gives the base time to really absorb and retain the wax through the resultant cooling/ hardening.
Next you must scrape the base of the board in a tip to tail direction only with a firm, straight plastic or metal edged scraper. Try to remove all wax to create a perfectly smooth flat base. This part is the most tiring, but also very important. To remove particularly stubborn sections of wax you can momentarily bend the scraper a little to focus your energies on a smaller area.
When the excess wax has been removed its then time to polish the base with a soft bush in the same fashion as when ironing. Afterwards sternly use the harsh brush (often have metal protrusions) in a tip to tail only fashion to add structure to the base.
There you go, its ready to ride!
Generally it’s a good idea to wax your board once every 3 days of use. Waxing should be more frequent if you ride really hard or enjoy ice or hard-packed snow conditions. To reduce the board damaging effects of oxidation of the base from UV radiation/ other influences from the environment why not wax the base for transport and long snowless summers.
How To Wax A Snowboard Resources
Learn to Snowboard: How to Stick to Rails Like Glue!
How To Stick to Snowboard Rails Like Glue! 3 Secrets that will Radically Improve Your Jibbing Skills!This article is for any rider who is looking to improve their snowboarding skills on and off rails....
Snowboarding Tips - For Beginners And Advanced Alike
Snowboarding is a great way to get the benefits of exercise and enjoy the great outdoors in the winter months. Whether you are an experienced or a first time snowboarder it is important to consider several...
An introduction to half pipes
Let's face it, when snowboarding, anything that isn't flat creates an almost over powering urge to try to ride and half pipes are no exception to this. After gazing upon the glory of a half pipe it is...
Snowboard Safety: Injury Prevention and Treatment
Snowboarding is one of the most popular snow sports and like any other physical activity, it is susceptible to injury. However if the right precautions are taken and the correct protective gear is worn,...
Snowboarding Isn't Just For Kids Anymore
Pain and injury avoidance techniques for snowboarding are invaluable but not well known. If you know how, you can avoid the two biggest mistakes that first time snowboarders make. A positive experience...
Further How To Wax A Snowboard Related Resources...
Website Needs To Be 'Scene (Calgary Sun)
Winter is leaving its mark on www.calgarysun.com. In particular, SnowScene, Calgary's weekly ski and snowboard report, is covering the thrills and spills of the two sports close to the hearts of Albertans.
Winter is leaving its mark on www.calgarysun.com. In particular, SnowScene, Calgary's weekly ski and snowboard report, is covering the thrills and spills of the two sports close to the hearts of Albertans.
Winter Lowdown (Boise Weekly)
By BW Staff.
By BW Staff.
Jon Easdon Turned A Belief In The Little Things Into Two Big Best Of Wins (Colorado Springs Independent)
Jon Easdon turned a belief in the little things into two big Best Of wins Blindside, after less than a year, rules the snowboard and skateboard categories.
Jon Easdon turned a belief in the little things into two big Best Of wins Blindside, after less than a year, rules the snowboard and skateboard categories.
2009 Snowboard Are Here: One New Snowboarding Company Is Taking The Competition To A New Level (PRWeb Via Yahoo! News)
Morrell Boards takes a unique approach of allowing their customers to create their perfect snowboard (Rite Ride).
Morrell Boards takes a unique approach of allowing their customers to create their perfect snowboard (Rite Ride).
